Trip computer

Citroen C4 / Citroen C4 Owner's Manual / Multifunction  display / Trip computer

To obtain display and selection of the different types of information, give short

To obtain display and selection of the different types of information, give short presses on the end of the windscreen wiper stalk.

To reset trip computer information to zero, press continuously for a few seconds on the end of the stalk when one of the information types is displayed.

Display A

Display A

The trip computer provides 5 types of information, which can be accessed by pressing successively on the end of the control stalk.

• Range
• I nstantaneous fuel consumption
• D istance travelled
• A verage fuel consumption
• A verage speed

To cancel the display of the trip computer information press a sixth time

Display C or NaviDrive

Display C or NaviDrive

3 types of instantaneous information:

- Range
- Instantaneous consumption
- Distance remaining to be travelled

It also gives you access to 3 types of information for two Journeys 1 and 2:

- Distance travelled
- Average consumption
- Average speed

Display C or NaviDrive (continued)

The journeys

Journeys 1 and 2 are identical but independent of each other. For example, you can use Journey 1 for daily calculations and Journey 2 for monthly calculations.

To reset a journey to zero

When the desired journey is displayed, give a long press on the end of the wiper stalk.

Permanent display

Pressing the "Mode" button causes the trip computer information to be displayed permanently.

Enter the distance to be travelled

- P ress A.
- U sing B select the trip computer icon, then validate by pressing C.
- Select distance entry, using B.
Validate your choice by pressing C. - T o choose the distance, select the figure to be modified using B then validate using C.
- U sing B, adjust the value then validate using C.
- Validate with "OK" in the display.

To display the log of alerts or status of functions

- P ress A.
- U sing B select the trip computer icon, then validate by pressing C.
- S elect the log of alerts or status of functions.
- O nce the list is displayed, scroll through the list using B.
- P ress D to return to the permanent display.

Display A

Display A



This indicates the mileage that can still be travelled using the fuel remaining in the tank.

When the distance remaining to be travelled is less than about 25 km (approx. 15 miles), only three dashes are displayed.

After resetting the computer, the indication of remaining range is only reliable after the vehicle has been used for a certain time.

Average fuel consumption

Average fuel consumption

The average fuel consumption is calculated from the last reset of the computer.

Instantaneous fuel consumption

Instantaneous fuel consumption

This is calculated from consumption over the previous 2 seconds. This function is only available when travelling at over 30 km/h (approx. 20 mph).

Average speed

Average speed

The average speed is obtained, from the last reset of the computer, by dividing the distance covered by the time taken (ignition on).

Distance travelled

Distance travelled

It indicates the distance travelled since the trip computer was last reset to zero.

Distance remaining

See previous page.

Display C or NaviDrive  (continued)


    See also:

    Diesel engines HDi 173 - V6 HDi 208 (with particle filter)
    1. Screen wash and headlamp wash reservoir. 2. Power steering and suspension fluid reservoir. 3. Engine coolant reservoir. 4. Engine oil gauge. 5. Engine oil topping-up. 6. Air filter. 7. Brak ...

    Towing your vehicle
    On the front bumper, unclip the cover by pressing at the bottom. Screw the towing eye in fully. Install the towing bar. Switch on the hazard warning lamps on the towed vehicle. Place ...

    Headlamp adjustment
    To avoid causing a nuisance to other road users, the height of the headlamps should be adjusted in relation to the load in the vehicle. 0 . 1 or 2 people in the front seats. -. 3 people. 1. 5 ...

    // -->